Mega timers - Programming - Arduino Forum
...Where will I get information about the timer output to Mega pins assignment? like the attachment for UNO....
https://forum.arduino.cc/t/mega-timers/672091
Handling Timer Overflow Interrupts - Arduino Forum
...I clear the timer, set it up in Input Capture Mode, set the pre-scaler to ClkIO/1024, and enable Overflow interrupts, as the event I'm timing can take up to 10 seconds, which means the timer may overflow twice. I maintain a software count, in a uint32_t that is increment by 65536 every time an overflow occurs....
https://forum.arduino.cc/t/handling-timer-overflow-interrupts/489152
Timers on the Arduino Mega 2560
...Hi all, I am contemplating a project where I would want to have three independent timer interrupts running simultaneously and want to understand how the Arduino platform uses the timers on the Mega (ATMega 2560-based boards). As I understand, the ATMega 2560 has four 16-bit timers available and two 8-bit ones. Ideally I would like to hijack three of the 16-bit timers. My question is, I know ......
https://forum.arduino.cc/t/timers-on-the-arduino-mega-2560/57523
Solved: SP 2019, timer job not working. | Experts Exchange
...SP 2019, timer job not working. Hi, I need help with SP 2019 on which timer job for Microsoft SharePoint Foundation Usage Data Processing is not working and that is causing WSS_Logging database to grow. All services are running but when i click Run Now for this timer job, nothing happened....
https://www.experts-exchange.com/questions/29262926/SP-2019-timer-job-not-working.html
Start a timer when button is pressed - Arduino Forum
...I am creating a timer for a race. I have a photosensor that has a laser pointed to so when someone crosses the finish, it trips the sensor, and the system logs the racer's time. I am using millis() to time the race, but I need the timer to start when I push the button. I have tried using edge detection to start the timer, but the timer starts when the program starts, not when the program ......
https://forum.arduino.cc/t/start-a-timer-when-button-is-pressed/856752
Uno R4 Wifi Watchdog Timer - Programming - Arduino Forum
...Thanks, I found the example and was able to add the WDT to my code. Unfortunately, the WDT has a maximum timeout of 5592ms on the Uno R4. This proves to be absolutely useless when using the Uno R4 on the ArduinoCloud as some cloud stuff takes longer than 5592ms (for example reconnecting to WiFi or sometimes even connecting to the ArduinoCloud). If anyone has a better WDT solution for the Uno ......
https://forum.arduino.cc/t/uno-r4-wifi-watchdog-timer/1167819
Making a timer - Programming - Arduino Forum
...Hello, I am making a Timer with my LCD Display. I do not have any input connected at this point in time. I am trying to make my timer display count down but I do not know how I can do this. I was hoping someone may assist me with the coding of this. I have not touched arduino in a while so I am a little dusty....
https://forum.arduino.cc/t/making-a-timer/313423
Use of Timer 2 in Arduino UNO
...Iam beginner with arduino and learning Interrupts , Stuck at a point while doing my project , I want to know how to use timer 2 for interrupt , i wrote a small peace of code , after every 10ms i want to monitor a sensor input ....
https://forum.arduino.cc/t/use-of-timer-2-in-arduino-uno/652515
[esp32] How to disable, reset and again enable timer
...I am trying to disable and again enable timer on my ESP32 but I have a problem resetting or restarting it. I don't have right words for that, but basically need him to start counting from 0 again. In arduino it is TCNT1 register. I was trying timerRestart(timer) function but without success. Code below should print out 2 zeros but it prints 0 and 30 because counter inside timer do not resets ......
https://forum.arduino.cc/t/esp32-how-to-disable-reset-and-again-enable-timer/693221
Programmable switch timer - General Guidance - Arduino Forum
...I have beginner skills on arduino, and I kind of jumped the gun into a project for school, to build a programmable switch timer, it has 4 buttons The switch is to be able to program on and off times of a bulb, it should be able to set 2 programs daily for each day of the week(i.e. i can manually program 2 on/off times for each day Monday through sunday).This also implies that date, time are ......
https://forum.arduino.cc/t/programmable-switch-timer/1272709