Alla svenska städer
Hårborttagning | Billiga hotell | Privat Kredit - Låna pengar | Tågbiljetter | Tjäna pengar
Micro SD Card failure - Bambu Lab Community Forum
...Just had the Micro SD card fail and cause a bunch of weirdness. Specifically Bambu Studio would indicate it had sent the new print job but the printer would then run the last job for some random reason. There was no err?...
https://forum.bambulab.com/t/micro-sd-card-failure/20895
A1 wont print silk - Bambu Lab Community Forum
...I got my A1 on December 22, on the 24th it stopped extruding filament. Replaced filament sensor, new extruder gears and new nozzle. Now, I can?t get silk to print with AMS. I can print with any other filament other than silk I have been going back and forth with support, trying to figure this out. It will load filament totally fine, will unload fine. When it goes to print, that?s where it ......
https://forum.bambulab.com/t/a1-wont-print-silk/51726
Custom Filaments not syncing to AMS - Bambu Lab Community Forum
...I?ve already read the Bambu wiki that explains how you set up custom filament in the slicer. Though a bit obtuse, the process is not too complicated. Every time I configure the AMS in Bambu Studio, it will show up correctly before quickly disappearing.This makes it impossible to ensure the filament has the correct pressure advanced settings. While doing random test, I did get a custom ......
https://forum.bambulab.com/t/custom-filaments-not-syncing-to-ams/49902
Micro SD card full? - Troubleshooting - Bambu Lab Community Forum
...Hello, I am getting a little tired of the compulsory use of the micro SD card. Specially when It has forced me to cancel prints near the end of the print due to the card being full? I am guessing this is the issue because I don?t keep time lapses. and my camera stopped working after replacing the damn circuit board where the SD card goes. I have never had this issue before. It?s only when ......
https://forum.bambulab.com/t/micro-sd-card-full/190570
How to disable AMS lite connected to A1 mini in Bambu Studio? [Solved]
...I have new A1 mini. Today I tried for the first time to use the external spool holder for TPU filament (Ninjaflex). It took a while to figure out to enable the external spool in Bambu Studio. The external spool was available as a choice only after disconneting the AMS lite from the A1 mini. Is it possible to disable the AMS lite for using the external spool of the A1 mini without disconnecting ......
https://forum.bambulab.com/t/how-to-disable-ams-lite-connected-to-a1-mini-in-bambu-studio-solved/65783
SD card not recognized - Troubleshooting - Bambu Lab Community Forum
...My p1p no longer reads sd cards. I have the original and it works on my computer but not the printer. I tried another sd card from my phone with the same result. Both work with my computer. I have factory reset the printer. Thanks so much for any and all insights!...
https://forum.bambulab.com/t/sd-card-not-recognized/90428
Help diagnose floating cantilever warning - Bambu Studio - Bambu Lab ...
...Hopefully these screen grabs will detail the feature I?m struggling with. In this example it slices fine. You can see there are 2 non-intersecting holes....
https://forum.bambulab.com/t/help-diagnose-floating-cantilever-warning/133698
Variable infill - Bambu Studio - Bambu Lab Community Forum
...I?m a former Cura user (lol, sounds like a disease!). In Cura I could selectively specify the infill density on the part/model to, say, strengthen where a bolt goes through, or a bolster a high stress area. I can?t seem to find a similar function in BambuStudio. I?m pretty sure it would be done with ?Modifiers? but I can?t figure out how. Has anyone been able to do this? Any help ......
https://forum.bambulab.com/t/variable-infill/76810
How To Print Polypropylene PP Filament - Bambu Lab X1C - Bambu Lab ...
...Getting started printing on the X1C Filament is FormFuture Centaur PP Polypropylene - Natural Print bed used was the engineering plate with pp polypropylene tape applied Printer is X1C Ocra Slicer Tips: Start off with a low temp melt filament like pla before you load the pp filament into the extruder and nozzle. We don?t want to grind up the pp filament. I like to use a window film tinting ......
https://forum.bambulab.com/t/how-to-print-polypropylene-pp-filament/47632
SOLVED: Change Bambu Lab username?
...Cannot seem to find anywhere where I can change my username from user_NNNNN to something a bit more useful. It would be o.k. if this didn?t show up on my printer, in Bambu Studio, and elsewhere. But kind of annoying whe?...
https://forum.bambulab.com/t/solved-change-bambu-lab-username/18668
Kalix Kallax Kallinge Kalmar Kalvsund Kangos Karby Kareby Karesuando Karlholmsbruk Karlsborg Karlshamn Karlskoga Karlskrona Karlstad Karlsvik Karungi Kastlösa Katrineholm Kattarp Kaxholmen Kebal Kil Kilafors Killeberg Kilsmo Kimstad Kinna Kinnared Kinnarp Kinnarumma Kiruna Kisa Kivik Kjulaås Klagstorp Klevshult Klingsta och Allsta Klintehamn Klippan Klippans bruk Klockestrand Klockrike Klutmark Klågerup Klädesholmen Kläppa Klässbol Klöverträsk Klövsjö Knislinge Knivsta Knutby Knäred Kode Kolbäck Kolsva Konga Kopparberg Kopparmora Koppom Korpilombolo Korsberga Korskrogen Korsträsk Koskullskulle Kosta Kovland Kramfors Krika Kristdala Kristianopel Kristianstad Kristineberg Kristinehamn Kristvallabrunn Krokek Krokom Kulltorp Kullö Kumla Kumla kyrkby Kummelnäs Kungsbacka Kungsberga Kungsgården Kungshamn Kungshult Kungsängen Kungsäter Kungsör Kungälv Kusmark Kuttainen Kvibille Kvicksund Kvidinge Kvillsfors Kvisljungeby Kvissleby Kvänum Kyrkberget Kyrkheddinge Kyrkhult Kyrksten Kåge Kågeröd Kåhög Kållekärr Kållered Kånna Kårsta Kälarne Källby Källö-Knippla Kärda Kärna Kärsta och Bredsdal Kättilsmåla Kättilstorp Kävlinge Köping Köpingebro Köpingsvik Köpmanholmen