Concrete Anchor Pullout Calculator (USA) ? ConcreteToolkit.com
...Calculate the pullout capacity (?Npn) for cast-in headed anchor bolts and hooked J/L-bolts in concrete per ACI 318-19 Section 17.6.3. Includes bearing area calculation, cracked/uncracked concrete factors, demand vs. capacity check, and 2026 USA material cost estimate....
https://concretetoolkit.com/calculators/concrete-anchor-pullout-calculator-usa/
ACI 318-19 Chapter 17: Anchor Limit States Explained
...All ACI 318 Ch. 17 anchor limit states: steel strength, concrete breakout, pullout, side-face blowout, pryout, and the §17.8 interaction check, with equations. Every anchor failure in a real earthquake corresponds to one of the seven limit states in ACI 318-19 Chapter 17....
https://www.panacheg.com/blog/aci-318-19-chapter-17-anchor-limit-states
Concrete Headed-Anchor Pullout (ACI 318-19 17.6.3)
...A 3/4-in headed bolt (0.654-in^2 head) in 4,000-psi cracked concrete pulls out at a factored 14.6 kip - and unlike breakout it does not depend on embedment, so deepening the anchor does not raise it....
https://roughlogic.com/tools/concrete-anchor-pullout/
Anchor Bolt Calculator - ACI 318-19 Tension & Shear Capacity
...Pullout strength Npn applies only to headed and some hooked anchors. It equals psi_c,P x 8 x Abrg x f'c per §17.6.3.2.1, where Abrg is the net bearing area under the anchor head....
https://concretecalculate.com/engineering-calculators/anchor-bolt-calculator/
Concrete Anchor Pullout Strength Calculator - Gera Tools
...Calculates the concrete breakout cone strength for a single cast-in or post-installed anchor per ACI 318-19 Chapter 17. Enter concrete f'c, embedment depth, and edge distance to get the design tension breakout strength with edge-distance reduction applied....
https://geratools.com/concrete-anchor-pullout-calculator
Anchor Bolt Design Calculator (ACI 318-19 Ch.17)
...The anchor bolt design calculator evaluates the tension and shear strengths of a SINGLE cast-in anchor in concrete following ACI 318-19 Chapter 17, using SI units (MPa, mm, N)....
https://reuven.tools/tools/anchor-bolt-design/
Anchor Bolt Pullout (Concrete Breakout) Calculator
...This calculator determines the basic concrete breakout tensile capacity Nb for a single cast-in anchor bolt far from edges and in cracked concrete, per ACI 318-19 Equation 17.6.2.1a....
https://calculatorhub.com/tools/anchor-bolt-pullout-calculator/
Anchor Bolt Design Calculator ? ACI 318-19 | ISS Engineering
...Design and verify cast-in anchor bolts with automated compliance checks for all failure modes defined in ACI 318-19 Chapter 17. Interactive graphics, step-by-step calculations, and one-click PDF export....
https://isseng.net/calc-anchors.html
Cast-In Headed Anchor in Concrete (ACI 318 Ch. 17)
...Check a single cast-in headed anchor for tension, shear, and combined interaction per ACI 318-19 Chapter 17....
https://engcanvas.com/templates/concrete/cast-in-anchor-concrete
Anchor Bolt Tension/Shear Interaction Calculator (ACI 318-19)
...This calculator implements the complete ACI 318-19 Chapter 17 anchoring-to-concrete provisions, covering every failure mode from steel rupture to concrete breakout, pullout, pryout, and side-face blowout....
https://simulations4all.com/simulations/anchor-bolt-tension-shear-interaction-calculator
Pajala Pauliström Persberg Persbo Pershagen Perstorp Persön Pilgrimstad Piperskärr Piteå Porjus Pukavik Påarp Pålsboda Påläng Påryd Påskallavik